After I reassembled the forks I couldn't resist to do a little mock assembly. I'm going to tear it back down to drill the holes in the frame to run the wiring and cables, but here is a peek of it's stance.
Wednesday, November 17, 2010
Fork Lube Job
First I cleaned the bushings and unscrewed the fork springs, then I scrubbed the springs down in my trusty trash can of gasoline. (it was full when the project started)
Then I gave everything a good lube job, I wasn't sure what I should grease so I greased everything.
Below I reinstalled the bushings and dust cap on the forks then screwed the springs back into the fork arms.
Friendly Tip Below
PUT YOUR BUSHINGS AND CAP ON BEFORE YOU SCREW THE SPRING IN
Friday, November 12, 2010
Frame Update
I installed the forks and swing arm. I will post more pictures of the fork installation once I find my pictures.
The right hand image is a picture of my future brake light that i got from www.superbrightleds.com.
Handlebars and Controls
I painted my 19 mm intake I purchased (thanx orangerobin) on www.Mopedarmy.com and painted my handlebar clamps, then I installed the controls and replaced the grips with some Kawasaki grips a friend gave me. They seem to be much better than the ones that came with the controls. I was a little disappointed that there wasn't a brake light switch holder :(. Now i'm on the hunt for some new M7x35 socket cap bolts to mount the handle bars. This is what my current ones look like, I'll clean them up and use them if i have to.
Labels:
brake light,
controls,
handlebars,
intake,
Treatland.tv
Sunday, October 31, 2010
Order New Part (Thanx Google)
Since i finally got my Google check, i decided it was time to buy some more parts.
I ordered this batch from Treat Land, the descriptions of the products on the site
crack me up. (you should check them out)
I've always had great service with them and 1977 Mopeds it just all depends on
who has what in stock.
let the list begin. :)
I ordered this batch from Treat Land, the descriptions of the products on the site
crack me up. (you should check them out)
I've always had great service with them and 1977 Mopeds it just all depends on
who has what in stock.
let the list begin. :)
bikemaster black superbike low rise handlebars |
lusito complete throttle control set - black |
moped rear brake cable |
moped front brake cable |
moped throttle cable for all mopeds |
puch moped one speed E50 clutch cable |
puch BLUE hi tension E50 clutch spring |
more expensive moped inner tube |
I also ordered an intake for my carb, that should be in around the same time.
w00t!
Labels:
1977Mopeds.com,
cables,
controls,
handlebars,
intake,
tires,
Treatland.tv
Monday, October 25, 2010
Installing Engine Internals
I finally decided it was time to start putting stuff in the casing. w00t!
Giving the e50 one more bath before I put it to work. |
Next, I'm going to seal it up today and start the installation of the top end.
Adding Area For Gasket
We didn't trust that there was enough area available for the gasket to make a good seal where the engine and the cylinder meet. So Bill thought it would be a good idea to add some area to the engine with some J-B Weld. So what the hell it couldn't hurt right. Here we go.
Bill prepping the weld |
We taped off all of the areas we didn't want the weld to get on and put a piece of tape between the two case halves to prevent the case from sticking together. |
Cutting off the excess with a razor blade |
Some soft filing to make flush. |
After we finished the next day I was organizing my work area and realized a piece of the weld came off :(
I think it was due to the very old JB "kwik" weld we used.
I had to rip the top off to get it open :) |
So the next day I went back to Auto Zone and picked up the J-B Weld Stik and redid the side that fell off.
It worked great, no need to tape anything off.
Side finished with the stick |
Port Matching (Fix)
After visiting the Moped Army, I was told my best bet would be to J-B Weld the hole I created. So I went out and bought some "slow" curring J-B Weld and gave it a shot.
I used heat shrink to fill in the screw hole trying to prevent the weld from seeping into the hole. It ended up working really well. |
After it dried over night, we scored the weld down the middle and it cracked it open with out a fuss. |
Other side |
I hope it holds.
Port Matching e50
I want to start out by saying I know it's not perfect but once i went too deep on one side I didn't want to push my luck, I figured this is better than nothing.
This is for a "Cheapo 70cc Cylinder Kit" from www.1977mopeds.com
This is for a "Cheapo 70cc Cylinder Kit" from www.1977mopeds.com
Install the gasket to mark the area that needs removed. |
My markings with the gasket and studs removed |
Some of the tools I used. |
The First Side It went pretty well I did smooth it out a bit more afterthis picturewas taken. I used a file and sand paper for that. |
Tuesday, October 19, 2010
Main Gear Bearings
All went as planned, took off the old bearings with my puller and pressed the new ones on.
Pulling off old bearings |
Image of bare shaft |
Installed snap ring |
Image of both bearings installed, I used a press for the one on the right and a rubber malled for the one of the left. |
Labels:
Bearings,
Puch Magnum,
Puch Parts
Sunday, October 17, 2010
Painted sprockets and brake assembly
I painted my rear wheel sprocket, brake assembly and my engine gear sprocket.
I'm going to reassemble the rear wheel tomorrow after the paint has had time to completely dry
I'm sure it's not going to last long but it's worth a shot.
Saturday, October 16, 2010
Installed Wheel Bearings
These went in pretty easily a lot faster then getting the old ones out. I laid the bearings flush and gave it a whack with a rubber malled.
Bearing 1 |
Bearing 2 Side note: I noticed I didn't have the bearing in far enough after I took this picture. Make sure your bearing is pressed in far enough. Don't forget the spacer between the bearings |
Rebuilding Idle Sprocket
I rebuilt my idle sprocket last night, it went pretty well. I cleaned the bearings, sprocket, and the gear stopper thing. I'm not sure what they are called but it's the little pieces that stops the sprocket from moving backwards.
bearings, springs, and gear stoppers soaking in carb cleaner |
Back side of Idle Sprocket with clean bearings packed in new grease |
Once all the bearings are greased up it should be pretty easy to flip the sprocket over with out losing any bearings |
I'm not sure what these are called but they seem to hold down the clips that stop the sprocket from moving backwards and the screw cap. |
Installing the clip things I was just referring to |
and now the 3 ring covers |
Installing the clean bearings and grease on the front side over the sprocket |
All the bearings installed |
Adding grease to the screw cap After that I screwed the cap on (counter clock wise) and tapped it tight then spun it around a couple dozen times and wiped all the excess grease that seeped out. |
Labels:
Bearings,
grease,
idle sprocket,
sprocket
Subscribe to:
Posts (Atom)